The job: a GE GFW850SSN0WW front-load washer, running again
Last updated:
Case Study · GE Washer Not Spinning · Lynnwood, WA
GE washer not spinning in Lynnwood: a failed inverter board.
This GE front-load washer in Lynnwood would start a cycle, run for a few minutes, then stop and show “End.” Fill and drain worked, but in the spin test the drum never reached high speed. The inverter board, which drives the motor, had failed. We replaced the inverter board assembly and ran a full cycle to confirm. Real photos from the job below.
- Location: Lynnwood, WA
- GE GFW850SSN0WW front-load washer
- Symptoms: stopped a few minutes into the cycle and showed “End”, wouldn’t spin at high speed
- Found: fill and drain tests passed, spin test failed; inverter board not driving the motor correctly
- Repair: inverter board assembly replaced, full cycle with high-speed spin confirmed
- Diagnosed & repaired by Max, owner-technician
Licensed & Insured
90-Day Warranty
Owner-Operated
What happened
From a GE washer that wouldn’t spin to a full cycle again
The complaint
The homeowner’s GE GFW850SSN0WW front-load washer would start a cycle normally, then stop after a few minutes and show “End” on the display. The laundry came out unfinished.
The diagnosis
The washer had several error codes stored. We ran its service tests: water fill and drain both passed, but in the spin test the drum never got up to high speed. The inverter board, the control that powers the direct-drive motor, wasn’t driving the motor correctly.
The fix
We ordered and installed a new inverter board assembly, then ran the washer through a full cycle, including high-speed spin. It finished normally. The repair carries our 90-day warranty.
Real photos
This job, start to finish
Front panel off to get at the tub, motor and wiring
The inverter board sits at the base, next to the direct-drive motor it powers
The old and new inverter boards side by side
The underside of the inverter board
New inverter board installed and wired back up
Rating plate: model GFW850SSN0WW
Review
What the homeowner said
"GE Front Load Freestanding Washer would starts but then stop after a few minutes and display END. Max responded within a day , ordered the part that was likely the culprit, and repaired it in one 1hr visit. Great communication, tidy and no nonsense. Ace Appliance Service will now be my go-to appliance repair service."
Why choose us
Why Lynnwood homeowners call Ace Appliance Service for washer repair
We test before we order parts
A washer that won’t spin can be a door lock, a drain problem, the motor or the board that drives it. Running the service tests first narrows it down before anything gets ordered.
One technician, start to finish
The same owner-technician diagnoses the problem, orders the part, and comes back to install it. No call center and no subcontractors.
90-day warranty
WA Contractor #ACEAPAS774K6. We’re an independent repair company, and this repair is backed by our 90-day warranty. See our washer repair page for more.
Questions
GE washer not spinning in Lynnwood: FAQ
Do you repair GE washers in Lynnwood?
Yes — this case study is a GE front-load washer in a Lynnwood home. We serve Lynnwood, Edmonds, Mountlake Terrace, Everett, Bothell and the rest of King and Snohomish County.
Are you a GE authorized service provider?
No. Ace Appliance Service is an independent repair company, not a GE factory-authorized servicer. If your GE washer is still under its factory warranty, contact GE Appliances first. Outside that warranty, we diagnose and repair it ourselves, and our work carries a 90-day warranty.
How much does it cost to replace a GE washer inverter board?
It depends on the model and the part. We diagnose the exact cause on-site first, then give a clear price before any repair begins.
Are you licensed and insured?
Yes, Ace Appliance Service LLC is licensed and insured to work in Washington State. WA contractor license #ACEAPAS774K6.
What areas do you serve?
King and Snohomish County, including Seattle, Bellevue, Kirkland, Bothell, Edmonds, Lynnwood, Everett, Mukilteo, Mill Creek, Snohomish, Kenmore, Woodinville, Mountlake Terrace, Lake Forest Park, Shoreline, Redmond, Issaquah, Sammamish, Mercer Island, Clyde Hill, and Medina.
Common GE washer problems
Why is my GE front-load washer not spinning?
There are several possible causes: a door lock that isn’t engaging, water that isn’t draining, the motor, or the inverter board that drives the motor. Fill, drain and spin tests narrow it down. On this Lynnwood GE, fill and drain passed but the drum never reached high speed, and the fix was a new inverter board.
GE washer stops mid-cycle and shows “End”?
That means the washer ended the cycle early, usually because it detected a fault, and it often leaves an error code stored. On this job several codes were stored, and the spin test showed the motor wasn’t being driven up to speed. The cause was the inverter board.
What does the inverter board do on a GE washer?
On a direct-drive front-load washer like this GE, the inverter board controls the motor: it powers it and sets its speed for washing and spinning. When it fails, the washer can fill and drain normally but can’t spin the drum properly.
Ready when you are
Washer stopping mid-cycle or not spinning? Let’s find out why.
Call now for the fastest response, or send us a few details and we'll call you back within one business hour.
(425) 533-0823 Call Now · Same-Day ServiceMon–Fri, 8am–6pm