The job: a Wolf CG304P/S gas cooktop with a downdraft vent
Last updated:
Case Study · Wolf Cooktop Repair · Redmond, WA
Wolf cooktop repair in Redmond: two burners that kept clicking while lit.
This Wolf cooktop repair in Redmond was on a Wolf CG304P/S four-burner gas cooktop in a kitchen island. Two burners lit fine but kept clicking the whole time they were on. The old burners were badly corroded underneath, and this burner can't be taken apart and rebuilt, so we replaced both. Real photos from the job below.
- Location: Redmond, WA
- Wolf CG304P/S gas cooktop, 4 sealed burners, natural gas
- Symptom: two burners kept clicking even with the flame lit
- Found: heavy corrosion on the burner bases and igniter leads
- Repair: both burners replaced (this burner isn't serviceable, replacement only)
- Diagnosed & repaired by Max, owner-technician
Licensed & Insured
1-Year Warranty
Owner-Operated
What happened
From nonstop clicking to a quiet, steady flame
The complaint
The homeowner's Wolf CG304P/S sits in a kitchen island with a pop-up downdraft vent behind it. Two of the four burners would light, but the igniters kept clicking the entire time those burners were on. Cooking with a constant click-click-click isn't something you can live with.
The diagnosis
Wolf gas cooktops relight a burner automatically if they think its flame has gone out. A burner that keeps clicking while it's clearly lit means the ignition system isn't recognizing that flame. We pulled both burners: the bases were heavily corroded underneath, and the end of one igniter lead was corroded through. On this model the burner can't be taken apart and rebuilt, so cleaning wasn't a real fix.
The fix
We replaced both burners with new assemblies, each with its own electrode and lead, and reconnected them to the cooktop's ignition wiring. Then we lit every burner and checked the flame. Each one lit, stayed lit, and stopped clicking once the flame was on. The repair carries a 1-year warranty.
Real photos
This job, start to finish
Lifting out one of the clicking burners: corrosion all around the base
Underneath: heavy corrosion on the burner base
Corrosion on the end of the old igniter lead
The new burner: clean ports, no corrosion
The new burner comes with its own electrode built in
Both new burners installed
Final flame check on both repaired burners
Why choose us
Why Redmond homeowners call Ace Appliance Service for Wolf cooktop repair
We look before we replace
Constant clicking can come from moisture, a dirty burner, a switch, the spark module, or the burner itself. We pulled the burners and found the corrosion first, then explained why replacing them was the only fix that would last.
Only the parts that need it
Two burners were clicking, so two burners were replaced. The other two burners were working normally and were left alone. Every burner was lit and checked before we left.
Genuine Wolf parts, 1-year warranty
WA Contractor #ACEAPAS774K6. We use genuine Wolf parts, and this repair is backed by a full year on parts and labor. See our Wolf repair page for more.
Questions
Wolf cooktop repair in Redmond: FAQ
Do you do Wolf cooktop repair in Redmond?
Yes — this case study is a Wolf cooktop repair in a Redmond home. We serve Redmond, Kirkland, Bellevue, Sammamish, and the rest of King and Snohomish County.
Can a corroded Wolf burner be repaired instead of replaced?
Not on this model. The burner on this Wolf CG304P/S can’t be taken apart and rebuilt, so once the base and igniter are corroded the only real fix is a new burner. That’s why both clicking burners were replaced.
Do you use genuine Wolf parts?
Yes. We use genuine Wolf parts, backed by our 1-year parts and labor warranty. We’re an independent repair provider for Wolf, not a factory-authorized dealer.
How much does it cost to replace a Wolf cooktop burner?
It depends on the model and how many burners need replacing. We diagnose the exact cause on-site first, then give a clear price before any repair begins.
Are you licensed and insured?
Yes, Ace Appliance Service LLC is licensed and insured to work in Washington State. WA contractor license #ACEAPAS774K6.
What areas do you serve?
King and Snohomish County, including Seattle, Bellevue, Kirkland, Bothell, Edmonds, Lynnwood, Everett, Mukilteo, Mill Creek, Snohomish, Kenmore, Woodinville, Mountlake Terrace, Lake Forest Park, Shoreline, Redmond, Issaquah, Sammamish, Mercer Island, Clyde Hill, and Medina.
Common Wolf cooktop problems
Why does my Wolf burner keep clicking after it lights?
Wolf gas cooktops relight a burner automatically if they think the flame has gone out. If a burner keeps clicking while it’s clearly lit, the ignition system isn’t recognizing the flame. On this Redmond cooktop the cause was corrosion on the burner bases and igniter leads, and the fix was replacing both burners.
Wolf burner clicks even when it’s turned off?
Clicking with the knob off is usually moisture from a spill or cleaning, or a failing ignition switch. If it doesn’t stop once everything has dried out, it needs to be diagnosed.
Wolf burners won’t spark at all?
When a group of burners stops sparking together, it often points to a shared ignition part like a spark module. See our Wolf range repair in Kirkland case study for a real example.
Ready when you are
Wolf burner won't stop clicking? Let's find out why.
Call now for the fastest response, or send us a few details and we'll call you back within one business hour.
(425) 533-0823 Call Now · Same-Day ServiceMon–Fri, 8am–6pm