Last updated:

Case Study · Wolf GR486G · Sammamish, WA

Wolf oven not heating in Sammamish: the spark board had failed.

The oven on this 48-inch all-gas Wolf range in Sammamish had stopped heating. When the oven was turned on, there was no spark at the oven burner, so the gas never lit. The fault was one of the two DSI (direct spark ignition) boards under the cooktop. Max replaced it with a genuine Wolf board on November 17, 2026, and the oven lit and heated again.

  • Wolf GR486G 48" all-gas range, 6 burners + griddle
  • Symptom: oven not heating, no spark at the oven burner
  • Repair: one DSI board replaced with a genuine Wolf part
  • Oven tested and heating, 1-year warranty
Left side of a Wolf GR486G gas range in a Sammamish kitchen: two sealed burners, the griddle, and red control knobs
5.0 Google Rating Licensed & Insured 1-Year Warranty Owner-Operated

The part that failed

What a DSI board does on this Wolf

A gas burner needs two things to light: gas, and a spark at the right moment. On this range the spark comes from DSI boards, short for direct spark ignition. Each board makes the high-voltage spark that jumps from an electrode to the burner and lights the gas.

Two boards, side by side. This GR486G has two DSI boards mounted under the left side of the cooktop, below the two-burner section. Only one had failed, so only one was replaced.

The symptom it caused. With no spark at the oven burner, the gas had nothing to light it, and the oven stayed cold.

The old board and the new one. The original board was made by Invensys and carries Wolf part number 818676. The replacement is a genuine Wolf part made by Robertshaw. It looks different, but it fits the same mounts and connectors.

Old Invensys DSI board removed from the Wolf GR486G, lying on Wolf's printed DSI board replacement instructions next to a voltage tester

The visit, in order

From a cold oven to a working one

1

Confirm the symptom

With the oven turned on, there was no spark at the oven burner. No spark means the gas can’t light, which is why the oven wasn’t heating. That pointed to the ignition side of the oven rather than the gas supply. Our Wolf oven not heating guide covers the other causes by oven type.

2

Open the cooktop, replace the board

The grates, caps, burners and burner pan came off the left side of the cooktop to reach the two DSI boards underneath. Following Wolf’s own DSI board replacement steps, the failed board was unplugged, unscrewed from its standoffs and removed, and the new genuine Wolf board went in its place with the connectors and ground wire reattached.

3

Reassemble and test

The burner pan, burners and caps went back on. Then the oven was turned on again. This time it lit, and the oven heated. The repair is covered by our 1-year parts and labor warranty.

Real photos

From this Sammamish kitchen

Wolf GR486G 48-inch gas range in a Sammamish kitchen before the repair, with two burners and a griddle on the left and four burners on the right

The range on arrival: oven not heating

Wolf rating label showing model GR486G, Fitchburg, Wisconsin, 15,000 BTU per hour top burners and griddle, 120 volts

Rating label: model GR486G

Left side of the Wolf cooktop opened up from above, showing the burner orifice holders, gas lines and the DSI boards along the side

Cooktop opened: burners out, boards on the left

The two original Invensys DSI boards mounted side by side under the Wolf cooktop, with their wiring harnesses connected

The two DSI boards, side by side

The failed Invensys DSI board held in hand above the open Wolf cooktop, its label showing Wolf part number 818676

The failed board, Wolf part 818676

New genuine Wolf DSI board made by Robertshaw, held in hand above the open Wolf cooktop before installation

The new genuine Wolf board

New DSI board installed below the original board under the Wolf cooktop, wiring reconnected and the burners set back in place

New board in, wiring reconnected

Wolf GR486G range reassembled after the repair, with the oven turned on and its red indicator light lit

Back together, oven on and heating

Questions

Wolf range repair in Sammamish: FAQ

Do you repair Wolf ranges in Sammamish?

Yes. This job was a Wolf GR486G in Sammamish. We repair Wolf ranges, cooktops and ovens across King and Snohomish County, including Sammamish, Redmond, Bellevue and Kirkland.

Are you a Wolf authorized service provider?

No. Ace Appliance Service is an independent repair company, not a Wolf factory-authorized servicer. If your Wolf is still under its factory warranty, contact Wolf first. Outside that warranty, we repair it with genuine Wolf parts.

What warranty comes with a Wolf repair?

Wolf repairs come with our 1-year parts and labor warranty, and we use genuine Wolf parts, like the DSI board on this job. Ace Appliance Service LLC is licensed and insured in Washington State, WA contractor #ACEAPAS774K6.

How much does it cost to replace a Wolf DSI board?

It depends on the model and the board. We diagnose first and give a clear price before any repair begins.

Common Wolf range problems

Why is my Wolf gas oven not heating?

On an all-gas Wolf range, the oven heats with a gas burner, and that burner has to be lit. On this GR486G there was no spark at the oven burner because a DSI board had failed, so the gas never lit. The ignition parts, the gas supply and the controls can all cause the same symptom, so we test before replacing anything. See our Wolf oven not heating guide.

What is a DSI board on a Wolf range?

DSI stands for direct spark ignition. The board makes the high-voltage spark that lights the gas at the burner. This GR486G has two DSI boards under the left side of the cooktop. Only one had failed here, so only one was replaced.

My Wolf burners won’t spark. Is it the same problem?

It can be a related one. On another Wolf GR486G, in Kirkland, four burners wouldn’t spark because the spark modules had failed. Burners that spark but won’t stop clicking are usually something else: see why a Wolf range keeps clicking.

Ready when you are

Wolf oven not heating or burners not lighting?

Call now for the fastest response, or send us a few details and we'll call you back within one business hour.

(425) 533-0823 Call Now · Same-Day Service

Mon–Fri, 8am–6pm

Submitting this form sends a request — it doesn't reserve a specific appointment time. We'll call or text to confirm scheduling.

Call Now Text a Photo